Tag Archives: figurines

How It Works – Lost Wax Casting for Walter Bosse

Walter Bosse Hand Ashtray Casting Progression

Let’s dive into a little bit about the handmade casting process to understand a little more about what makes Walter Bosse and Vienna Bronze items special. The casting process used is “lost wax casting” or “investment casting.” Here all the steps and love that go into the creation of a Walter Bosse model:

Walter Bosse Hand Ashtray Master and Finished Model

1. Starting with a “master”

The process begins with the artist’s “master” pattern. There are several ways to make a master: A. directly from wax to mold; B. from wax to cast metal to mold; and C. from mold to master to secondary mold.

A. If we create a master out of wax and form a mold from it directly, the wax master could be melted down or damaged in the process. With this method, the master may be lost, along with the ability to create future molds from it. But at least we have one mold for the catalog.

B. Walter Bosse’s most common method of making a master was to sculpt the wax model by hand, create a metal cast from it, refine the metal model into a finished master, and then create a new mold. This way, the metal master is saved in order to continue making future molds. This is especially useful if the original molds get damaged or need to be replaced due to use over time.

C. If the master has been lost, but the mold is still available, we can cast from the existing mold, finish the model and save it for future mold making. The only downside is that there is about 1.52% shrinkage. (The general shrinkage allowance of brass is 3/16″ per foot.) We would not want to keep doing this over and over again, or the model’s size will continue to shrink with each new iteration. It’s good to keep a master with each mold if possible.

Walter Bosse Hand Ashtray Master to Wax to Mold

2. Making a mold

Rubber molds are preferred due to their longer shelf life. The creation of a rubber mold requires a vulcanizing press, which solidifies the shape using heat and pressure. Since quite a few of the original masters were lost, today remastering is often done with vintage Bosse pieces. In these cases, the vulcanizing process is less suitable, as the heat and pressure can be rough on vintage originals. Silicone molds are therefore used to preserve the quality of the vintage original (though the silicone molds do not tend to last as long). The vulcanized rubber molds end up lasting 1020 years with regular use, while silicone can last only 25 years.

It is necessary to cut a sprue hole in the mold, preferably somewhere inconspicuous on the model, running from the widest or thickest part to the thinnest part. This will be the path the wax/metal flows most easily into the mold. The master must then be cut from the mold, either by prying the mold open enough to remove the master, or cutting it in half entirely to make a two-part mold. It is best to cut the mold with a very sharp blade, such as a scalpel.

Walter Bosse Wax Tree

3. Wax

Molten wax is injected into the mold through the sprue hole. The wax model is then removed from the mold. An extended sprue is attached, which is then connected to a sprue base/post which makes up the center of the wax tree. We add as many wax models to the tree as possible to fill up all the available casting space.

Walter Bosse Casting Flask

4. Adding investment

Once the wax tree is full of models and ready to cast, it’s time to add the investment. The investment is what’s left when all the wax is burned out, leaving space for molten brass to be poured in. The flask/cuvette is placed around the tree. The investment medium, usually a type of plaster material, is mixed and added around the wax tree inside the flask. All of the bubbles must be sucked out, best performed with a vacuum or vibration method. Once the investment is cured, we are ready to burn out the wax.

Walter Bosse Casting - Molten Brass

5. Casting

The molten brass is poured, and begins to cure. Once the metal has cooled, the tree and investment material are removed from the flask. The investment is slowly and carefully broken away from the brass models. Once the models are fully cleaned of investment, they can now be snipped off the tree, ready for finishing.

Walter Bosse Finishing Process

6. Finishing

The models get a thorough grinding and polishing to ensure there are no flaws. They are then stamped on the bottom with “Bosse Austria,” and undergo the patented patina process. The model then goes through a second polishing in selected areas to highlight the gleaming beauty of the natural brass.

Walter Bosse Figurines

With finishing complete, a beautiful new Walter Bosse work of art emerges, ready to find a home!

Posted in Bosse Blog | Tagged , , , , , , , , , , | Leave a comment

Vintage Collection Available!

Walter Bosse Vintage

We recently acquired a selection of vintage new-old-stock items cast in the 1960s in Germany and are now releasing them for wholesale. Due to the vintage sand-casting and hand-finishing methods, every item is slightly different. Quantities are limited so once they sell out, they are gone! Stock sheet available by request, just drop us a line!

Check out the collection below:

Posted in Bosse Blog | Tagged , , , , , , , , , , | Leave a comment

Happy New Year: 52 × BOSSE

Happy New Year Everyone!

Recently, we’ve been inspired by all the pictures of your collections we thought we should start 2013 with a “picture a week” series from our collection. You can also follow the diorama series on Facebook and here on the blog.

So here it is, the first in the “52 × BOSSE” series:

Walter Bosse Bear Figurine Week 1 features Walter Bosse’s BO10 Bear with a top-hat and New Year’s sign .
Posted in Bosse Blog | Tagged , , , , , , , , , | Leave a comment

Walter Bosse in Fab’s Nifty ’50s Shop – 10/12

Walter Bosse on Fab's Nifty 50s Shop Calendar

We’re on the calendar! Modern Vienna Bronze will be having a Fab Sale in their upcoming Nifty ’50s shop. The sale starts 10/12 7 pm ET. In the meantime our online shop will be closed temporarily to support our sale on Fab.com. Please visit Fab.com starting on the evening of October 12 to purchase Walter Bosse bronzes!

If you have any questions, please contact us and we will be happy to help!
Posted in Bosse Blog | Tagged , , , , , , | Leave a comment

Walter Bosse Sale on Fab.com!

Walter Bosse Fab Sale Preview

Together with Fab.com we will be releasing a collection of items for sale soon in August. Check out their site and sign up to gain access to the sale and see the entire collection.

Posted in Bosse Blog | Tagged , , , , , , , | Leave a comment

Bosse Miniatures @ Canoe!

Canoe bosse

If you’re a Bosse lover in the Portland area you are in luck. Canoe has a lovely selection of Bosse figurines online and in their store as well as great mid century modern staples. Be sure to check out their beautiful store and purchase Bosse’s figurines online here!

Posted in Bosse Blog | Tagged , , , , , , , , | Leave a comment

Maquette’s Bosse Brass Figures

Maquette Bosse

Anna of Sub-Studio did a lovely guest post about Bosse’s brass figures on Samantha Hahn’s blog Maquette. Read the full article here!

Posted in Bosse Blog | Tagged , , , , , , | Leave a comment